P-G2Q FUEL DISPENSER

P-G2Q FUEL DISPENSER

FlowMeter Type : Optional

Accuracy : ±0.2%

Pressure Loss (kg/cm) :Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp): 1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition :-40~~+55degree

Control Type :Solenold Vale Control Type

Preset Function :Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight :215kg

Dimension(L×W×H) : 1060*550*1620(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 44 20ft: 22

on and noise of pump, finding whether leakage between axis end and pump cover, checking the excessive jump and swing of V wheel that is called belt wheel past, but now de fuel dispenser fined as V wheel in GBT/10412�002 General V Wheel. Don’t use water and oil with water to debug or cleanse tank in case of the pump and components of fuel dispenser is rust. Meanwhile preventing freeze water affect the normal operation because of low temperature. Regularly inspect and cleanse strainer, especial after installation a pipeline. With the working time get long the waste in pipeline or tank decrease, the period of checking and cleanse should considerably lengthen. But don’t exceed one month. The strength of V wheel should be appropriate because low strength result in no oil discharge out or inefficiency. Hi fuel dispenser gh strength, in another case, would increase the axis loan of motor and pump, fasting bearing abrasion of motor, pump and oil seal. Don’t adjust overflow valve to tight in case of increasing pump pressure so as to flux passing overflow valve, and well as noise, vibration and abrasion. Judgment for common failures Firstly, some failure analysis and correct judgment is necessary before maint fuel dispenser enance. The principle of first analysis then disassemble, easy first is the basis to judge trouble. The common failure phenomenon of vane pump is that no delivery, inefficient flux, leakage, noise and abnormal vibration. They will be introduced one by one. No delivery or inefficient flux Apart from pump failure other component and pipeline trouble may also result in this phenomenon. Here only introduce pump failure and inspection method. Exterior inspection: to check motor that maybe don’t work, or rotate in opposite direction, or lose V wheel. Reversal result from wrongly connecting two phase wire in motor or power supply. Adjusting strength of V wheel or changing a new one deal with wheel slip. However, the reason that motor don’t work are several, either electric or mechanical failure. Disconnecting V wheel at first,

odes per subnet.　　 - group addressing facilities are not used.　　 The Lontalk protocol offers four basic message services these being:-　　 fuel dispenser ACKD REQUESTRESPONSE UNACKD_RPT UNACKD　　 The service implemented on the IFSF network is ACKD. The ACKD service is were　　 a message is sent to a node and individual acknowledgements are expected back from　　 each recipient node. If the acknowledgements are not all received the sender times　　 out and retries the transaction. The number of retries and the time-out value are　　 variable and are set along with the network parameters by application level code　　 (layer 7 OSI model) see below for parameter description and the values set in the IFSF　　 net fuel dispenser work implementation:-　　February 2006 IFSF - STANDARD FORECOURT PROTOCOL FP2_1.90　　 COMMUNICATION SPECIFICATION　　 Page: 9　　 Priority Slot:1 Determines if message has　 fuel dispenser 　 priority over other messages improves response time of　　 critical messages (set to 1 to allow for the creation of　　 emergency messages).　　 Retry =3 Specifies the number of times a node will repeat　　 sending　　 A message if it doesn t receive an acknowledgement.　　 RPT_Timer : Not used Specifies how frequently　　 the message is repeated when using　　 unacknowledgedrepeated service.　　 RCV_Timer: Not used Star

llen as a share of GDP in most Asian countries, this does not mean that households are saving more. Excluding China and India, household saving has fallen sharply, from fuel dispenser 15% of GDP in the late 1980s to 8% today. The paradox is explained by the fact that wage incomes have risen more slowly than GDP as production has become more capital intensive. But this means that Asian consumers are spending a rising share of their income by borrowing or running down their savings. Amazingly, the savings rate of Japanese households has fallen more sharply than that of American households over the past decade. The IMF estimates that in Asia as a whole (including Japan as well AFP as the emerging economies) real growth in consumer spending has averaged a healthy 6 fuel dispenser .3% a year in 2005 and 2006. This suggests that Asian consumers can help sustain fairly robust GDP growth in Asia even if America s economy takes a dive. Some pundits have predicted a boom in Asian consumer spending over the coming years, which would help to fill the gap left by American consumers cutting back on their purchases. But if consumer spending is already rising strongly in As fuel dispenser ia, there is little pent-up demand ready to explode. On the other hand, spending by firms could pick up. After the Asian economic crisis in the late 1990s, investment plunged everywhere except China. It has remained relatively weak. However, as the overhang of excess capacity and debt has disappeared, capital spending is now starting to perk up across Asia. Japanese firms average return on assets now exceeds long-term interest rates by 5%, the widest margin for decades, according to Merrill Lynch. The Bank of Japan s latest Tankan survey of business confidence found firms to be unexpectedly cheery. Big Japanese manufacturers now report insufficient production capacity for the first time since 1991 and plan to increase capital spending by 17% in the year to March. Another reason for believing that Asian economies can dec